ORIGINAL PARTS & TRAINING

The KRYTAC Hop Up Bucking and Nub are made to perform optimally with the KRYTAC Rotary Hop Up, however they can be used in other hop up units. The construction and configuration of the bucking are the key things that set this hop up bucking apart from...

The KRYTAC Rotary Hop-up Barrel Clip secures the inner barrel to the hop-up unit. This two (2) pack comes with two replacement barrel clips that work with the KRYTAC Rotary Hop-up units.

The KRTYAC Trident MKII M4 receivers are the chassis from which the entire gun is formed and are made from aluminum alloy to be both strong and lightweight. The KRYTAC logo and right and left selector modes are stamped on the receiver. Included with the...

The KRYTAC Trident M4 PDW Outer Barrel is a 5" one piece metal barrel assembly that comes complete with all necessary parts for installation. One piece metal barrels are more stable than the archaic multi-piece design, they give the airsoft gun a more...

The KRYTAC Dust Cover Assembly comes with all of the necessary pieces to construct the dust cover; the cover, the hinge, and spring. The dust cover assembly is spring loaded to open when the charging handle is pulled. *This part is a non-firearm part...

The KRYTAC M4 Low Profile Gas block assembly is designed to be used in conjunction with AEG M4 outer barrels. This is a carbine length gas system assembly that is designed to resemble an AR15/M4 style gas impingement system and will complete the...

The KRYTAC Buffer Tube is made of metal and has a slightly larger internal diameter to help accommodate for more types of AEG batteries. The top of the buffer tube features numbers for the users reference for preferred stock position. *This part is a...

The KRYTAC Selector Switch Assembly comes complete with both the left and right selector. The KRYTAC Switch has been carefully designed to perform without impeding the shooters natural grip and shooting dynamics. Therefor the weak side selector is...

The KRYTAC M4 Sling Plate offers a sling attachment point at the rear of the lower receiver, on the left or right side, and is ideal for use with single point slings. The sling attachment points have been angled rearward to allow for a more natural and...

The KRYTAC Trigger Guard is made from aluminum and is designed to provide more room inside the trigger well for shooting with gloves. There are no sharp edges on the trigger guard and for a slight weight savings a speed hole can be found in the center of...

The KRYTAC Magazine release assembly features a metal construction and comes completely with spring, push button, and magazine catch. This magazine catch installs much more easily than standard magazine catches, there is a Philips head screw that...

The KRYTAC Charging Handle Assembly is constructed of metal and is responsible for pulling the bolt plate back and opening the dust cover. *This part is a non-firearm part and is intended for AIRSOFT use only.*

Receiver Pin Set for KRYTAC Trident M4 receivers. Designed to hold and lock the upper receiver to the lower receiver of your KRYTAC AEG.

The KRYTAC 8mm Solid Steel Bushings support the gears to stabilize rotation. Bushings are not created equal, though they look the same, the difference between one set of bushings to another is in the build materials and quality of construction. KRYTAC...

The Ambidextrous Selector Gear Set is specifically designed for the KRYTAC Trident Mechbox and Series of AEGs. These gears work in conjunction with the KRYTAC Ambidextrous Fire Selector Set to allow for fire mode selection by either left or right handed...

The KRYTAC Trigger Assembly comes complete with trigger and spring. Though it may seem insignificant, trigger characteristics are very important to accuracy. The KRYTAC trigger is specifically made with a very wide bow (front surface) and 90 edges to...

The Nautilus gearbox includes the anti-corrosive coating that give the gearbox it's unique color and the wire keep for the motor wires around the base of the gearbox. Each component on the KRYTAC Nautilus V2 Gearbox has been designed to perform at a high...

The KRYTAC 8mm Caged Ball Bearing Bushings support the gears to stabilize rotation and reduce friction and heat. Not all bearings are created equal, though they look the same, the difference between one set of bearings to another is in the build...

The KRYTAC Piston is one of the work horse components in the mechbox. The main construction of the piston is polymer. All of the polymer piston teeth are reinforced on both sides and the first 4 teeth made of metal. The 2nd to last tooth of the piston is...

The KRYTAC Cylinder Head is a hybrid construction of metal and polymer. It features an o-ring around the body to prevent air from leaking between the cylinder head and the cylinder. The KRYTAC Cylinder Head also features a dense rubber pad on the back to...

The KRYTAC Air Nozzle is constructed of high quality polymer to combat damage and wear and tear to maintain a tight air seal with the hop up bucking over time.

The KRYTAC Selector Plate features a polymer construction with metal contact tab. The metal tab on the selector plate completes the circuit for the mechbox when fire modes are selected, when SAFE is selected the circuit is incomplete ensuring the AEG...

The KRYTAC Tappet Plate is made of strong polymer to reduce wear and tear and to keep the AEG feeding properly.

The KRYTAC Enhanced Gear set comes complete with a bevel gear, spur gear, and sector gear. Each gear is made from a dense, hard, alloy and then heat treated for extra strength. Rockwell test figures on the KRYTAC Gear set show a much higher rating than...

The KRYTAC Nautilus reinforced 8mm ball bearing gearbox features an integrated MOSFET to regulate electronic signals and to protect the trigger contacts. The corners of the gearbox that surround the cylinder feature a smooth radius, as opposed to a 90...

Tokyo Marui Tactical Master Original Part. This slide is for the Tokyo Marui M9 gas blow back pistol. Light weight and ensures snappy cycling. Contents: x1 Tokyo Marui Tactical Master Original Part Slide

Tokyo Marui VSR-10 metal outer barrel for VSR-10, G Spec, or other VSR style TM sniper rifles. Items include : 1 x Tokyo Marui VSR-10 Original Parts # VSR-10

Features: High quality original Tokyo Marui loading nozzle for the M4A1 MWS Compatibility: Compatible with: Tokyo Marui M4A1 MWA, M4A1 MWS CQBR, M4A1 Carbine (GBBR) About Tokyo Marui: Tokyo Marui is a leading airsoft manufacturer that has...

The KWC Original Magazine Catch for KCB18DHN / KMB18 is the original part that comes with your factory stock airsoft gun. Items included: 1x KWC Original Magazine Catch for KCB18DHN / KMB18

This valve is for installation into the RWA Nighthawk/SPS/ KWC 1911 gas blowbacks that use the System 7 technology. It allows more reliable shot-to-shot power (FPS) and reduces your FPS down to a stable 290 - 310 fps which is more CQB friendly...

The original replacement of the GBB Nozzle Valve for the Tokyo Marui AR15/M4 MWS GBB Rifles (Original Part #MGG2-118).For more original parts, check out our Original Parts page!Compatibility:Tokyo Marui AR15/M4 MWS GBB RiflesIncluded:x1 Tokyo Marui M4A1...

Original spare part for the Tokyo Marui M4 MWS GBBR, this particular part is # MGG2-117. Please seek support for assistance to install it if you lack experience in repairing airsoft gun.

Original spare part for the Tokyo Marui M4 MWS GBBR, this particular part is # MGG2-116. Please seek support for assistance to install it if you lack experience in repairing airsoft gun

Original spare part for the Tokyo Marui M4 MWS GBBR, this particular part is # MGG2-114. Please seek support for assistance to install it if you lack experience in repairing airsoft gun

Original spare part for the Tokyo Marui M4 MWS GBBR, this particular part is # MGG2-113. Please seek support for assistance to install it if you lack experience in repairing airsoft guns.

This is the GHK AK Original Part# GKM-11-2-74U is an original replacement part for the GHK AK V2 GBBR Mags. Crafted out of high quality polymer and used as a stock part in your GHK Ak V2 Mags this is the perfect replacement that ant go wrong. Items...

This is the Tokyo Marui Hi-Capa 5.1 Original Parts # H51-76, which is the original stock part you get for your TM hi Capa 5.1 Directly from Tokyo Marui factory you can be assured nothing can go wrong with using this part. Items included: 1x Tokyo...

First party original partDesigned for VFC HK417 / G28 GBBR SeriesDesigned for VFC SR-25, SR-25 ECC, M110 GBBR SeriesNPAS Nozzle Can adjust the velocity by a 1.5mm hexagon wrench

This is the Tokyo Marui Hi-Capa 5.1 Original Parts # H51-83 perfect replacement part which cannot go wrong. Replacing this part will fix your leaky mags. Items included: 1x Tokyo Marui Hi-Capa 5.1 Original Parts # H51-83

This is an original part (#M4-15) for GHK M4 V2 GBBR series for under 1 joule versionHFC134a (approx. 0.5 Joule)Green Gas (approx. 0.6-0.7 Joule)CO2 (approx. 0.7 Joule)